Why do I get a message "Warning: couldn't find telemetry data"? Audio files created by other programs will also not be deleted. If you use Save Image as or Save Raw Image as the files created will not be automatically deleted. Note that files are only deleted if they have been created automatically by WXtoImg. Select Accept, then select Save Options from the Options menu. There are separate options for when to remove audio files, raw images, maps, and images. How can I automatically remove the older images and recordings?
Wxtoimg enhancements windows#
This will override the timezone settings set in the Windows control panel and can cause problems for WXtoImg. On Windows, check your autoexec.bat file for a setting starting with SET TZ=. On Windows open the Date/Time control panel (Start -> Settings -> Control Panel -> Date/Time), ensure that the "Time zone" is for a nearby city, that "Automatically adjust clock for daylight savings changes" is selected, and that the time is correct. The program tries to record polar satellites at the wrong time, what needs to be done?Ĭheck your time and timezone setting are correct. In this mode, only audio files can be saved, but the program will show the image as it is being recorded. Alternatively you can select Record only (show image if enabled) from Record under the File menu. If your computer still isn't fast enough to complete processing before the next image arrives consider upgrading your computer. Finally reduce the number of autoprocessing images and steps performed under Record in the File menu. Renaming these files requires significant extra time. You can further reduce processing by setting Maximum number of thumbnails to 0 in GUI Options in the Options menu.Īlso ensure that you have not selected Use for audio recordings/maps too in File Names and Locations under the Options menu. Setting Options -> Sharpen to none will marginally improve processing speed. Despeckle is generally inappropriate on WEFAX images because it degrades the fine lines in the maps. You can reduce processing time by disabling Options -> Despeckle (or setting it to none). Why do I only record every other image from geostationary satellites? You need to select the Record using WEFAX start/stop tones mode in the Recording Options. Why does it never stop recording when I try to record signals from geostationary satellites? Select either the Record when 2400 Hz carrier present or Record only when selected active APT satellites are overhead mode.
Most likely your receiver does not have squelch on the audio out. Why does recording start immediately and never stop recording when I try to record signals from polar orbiting satellites? Close other programs (including the mixer if it is running). The soundcard is in use by another program (possibly even the mixer). Why does the program "hang" with a "Status: opening soundcard." message? Some screen savers can also cause this problem, so setting your screen saver to none would be a good idea. Limiting the number and activity of other programs while WXtoImg is recording should eliminate the problem. The problem is caused by other programs doing a lot of activity or using a lot of CPU or memory or performing a lot of disk i/o while WXtoImg is recording. However it is best to minimise the occurrance of these splits in the first place. Under Options, enable Resync which will correct most of these problems. This may occur in just one place or in multiple places in the image. The image looks as though it has been cut horizontally and the upper or lower portion shifted left or right. Why is the image split (sometimes referred to as sync loss)? Follow the instructions carefully in the Required Calibration. Ensure that you have used the speaker (and not line) output from the receiver.
Wxtoimg enhancements install#
If this fails to eliminate the problem you may need to install or re-install the latest drivers for your soundcard.Įnsure that the audio cable from the receiver is attached to the soundcard Line 1 input. Try all soundcard values until you find one that works. Click OK and enter record mode again to test.
Wxtoimg enhancements Pc#
Open Record Options in the Options menu, and change the soundcard (even if your PC only has one soundcard you may need to change this for recording to work). Why do I get "Error: waveInOpen failed!" when WXtoImg tries to record? Also see the Slant Correction section in this manual. Information on adjusting the sampling frequency can be found in the Required Calibration. You need to adjust the sampling frequency. Why do I get a message "Warning: couldn't find telemetry data" when WXtoImg displays an image?
0 kommentar(er)
